Voron 0.1 Desktop System
The industry standard for compact, ultra-high-speed desktop FDM manufacturing. / 桌面级超高速 FDM 制造的行业标准。
Engineering Core / 核心工程理念
1515 Profile framework with integrated MGN7H linear motion. / 1515型材框架集成MGN7H直线运动系统。
Accelerations up to 10,000 mm/s² with Input Shaping. / 支持高达10,000mm/s²的加速度并配备共振补偿。
Supports multiple toolhead and wiring revisions (A through E). / 支持从A到E多种版本的工具头与接线方案。
Kirigami Bed Integration
Advanced laser-cut bed mounting system for 0.1 frameworks. / 适用于 0.1 框架的高级激光切割热床支架。
Technical Advantages / 技术优势
Reduced bed flex and improved vibration damping compared to standard mounts. / 相比标准支架大幅减少热床抖动并提升减震。
Integrated paths for heater and thermistor cabling. / 集成了加热器与热敏电阻的专用出线路径。
Installation Protocol / 安装协议
| Step / 步骤 | Action / 操作详情 | Warning / 注意 |
|---|---|---|
| Fold Check | Verify 90-degree internal angle / 校验90度内角 | Critical for bed level / 影响调平 |
| Heater Ground | Secure ground wire to frame / 地线锁紧至框架 | Safety requirement / 安全必须 |
| Y-Limit | Adjust rear extrusion clearance / 调整后型材间隙 | Avoid collision / 防止碰撞 |
Wiring Configuration (Type A)
Standard point-to-point electronic deployment. / 标准点对点电子系统部署方案。
Mainboard Mapping / 主板映射定义
| Port / 接口 | Device / 设备 | Signal / 信号类型 |
|---|---|---|
| Motor X/Y | 35STH Steppers | 2-Phase Bipolar |
| Bed Heater | 24V 60W Pad | PWM High Power |
| Endstop X/Y | Microswitches | Ground-Triggered |
Wiring Configuration (Type E)
Picobilical integrated toolhead communication system. / Picobilical 集成工具头通讯系统。
Interface Specifications / 接口规格
- Umbilical Connection: Single 14-pin high-density interface. / 单路14针高密度连接。
- Integrated Sensors: On-board ADXL345 and chamber thermistor. / 板载ADXL345与环境热敏。
- LED Control: Direct Neopixel RGB support. / 直接支持 Neopixel RGB 灯条。
Standard Print Guide
Guidelines for standard Voron 0.1 mechanical parts. / 标准版机械部件打印准则。
| Parameter / 参数 | Value / 建议值 |
|---|---|
| Material / 材料 | ABS or ASA (High Temp Resistance) |
| Perimeters / 壁厚 | 4 Layers (Minimum) |
| Top/Bottom | 5 Layers |
| Infill / 填充 | 40% Cubic / Grid |
System E Modified Prints
Specific part modifications for the Picobilical system. / 针对 Picobilical 系统的特定部件修改指南。
Required Changes / 必须进行的变更
- X-Carriage: Must use the E-revision mount for PCB clearance. / X滑块必须使用E版底座以避让PCB。
- Motor Mounts: Modified cable exit paths for Umbilical. / 电机座需使用修改过的线缆出口。
- Fan Duct: Redesigned for improved part cooling integration. / 重新设计的加强型散热风道。